National Instruments GPIB-ENET/100 Bedienungsanleitung

GPIBGetting Started with YourGPIB-ENET/100 andNI-488.2™for Mac OSGPIB-ENET/100 for Mac OSNovember 2000 EditionPart Number 322878A-01

About This ManualGPIB-ENET/100 for Mac OS xii ni.comRelated DocumentationThe following documents contain information that you might find helpfulas you

© National Instruments Corporation 1-1 GPIB-ENET/100 for Mac OS1IntroductionThis chapter lists what you need to get started and optional equipmentyou

Chapter 1 IntroductionGPIB-ENET/100 for Mac OS 1-2 ni.com❑One of the following shielded GPIB cables, which you can purchasefrom National Instruments:–

Chapter 1 Introduction© National Instruments Corporation 1-3 GPIB-ENET/100 for Mac OSYou can use either the Dynamic Host Configuration Protocol (DHCP)

Chapter 1 IntroductionGPIB-ENET/100 for Mac OS 1-4 ni.comThe LEDs show the current status of the GPIB-ENET/100. Table 1-1describes each LED.NI-488.2 O

Chapter 1 Introduction© National Instruments Corporation 1-5 GPIB-ENET/100 for Mac OSTime-Saving Development ToolsYour kit includes the NI-488.2 softw

© National Instruments Corporation 2-1 GPIB-ENET/100 for Mac OS2InstallationThis chapter describes how to install NI-488.2 for Mac OS and theGPIB-ENET

Chapter 2 InstallationGPIB-ENET/100 for Mac OS 2-2 ni.comInstalling the GPIB-ENET/100 HardwareComplete the following steps to install your GPIB-ENET/1

Chapter 2 Installation© National Instruments Corporation 2-3 GPIB-ENET/100 for Mac OSStep 2. Connect the CablesNoteIf you do not have an Ethernet cabl

Chapter 2 InstallationGPIB-ENET/100 for Mac OS 2-4 ni.comFigure 2-3. Connecting Power to the GPIB-ENET/100NoteDo not connect GPIB devices to your GPIB

SupportWorldwide Technical Support and Product Informationni.comNational Instruments Corporate Headquarters11500 North Mopac Expressway Austin, Texas

Chapter 2 Installation© National Instruments Corporation 2-5 GPIB-ENET/100 for Mac OSThe time required for assigning the IP address depends on your ne

© National Instruments Corporation 3-1 GPIB-ENET/100 for Mac OS3Ethernet ConfigurationThis chapter describes how to use the NI Ethernet Device Configu

Chapter 3 Ethernet ConfigurationGPIB-ENET/100 for Mac OS 3-2 ni.comUsing the NI Ethernet Device Configuration UtilityIf your network administrator tel

Chapter 3 Ethernet Configuration© National Instruments Corporation 3-3 GPIB-ENET/100 for Mac OS• *Unconfigured* indicates the device is configured to

Chapter 3 Ethernet ConfigurationGPIB-ENET/100 for Mac OS 3-4 ni.comChanging the Network SettingsYour GPIB-ENET/100 must be in network configuration mo

Chapter 3 Ethernet Configuration© National Instruments Corporation 3-5 GPIB-ENET/100 for Mac OSHowever, some DHCP servers do not implement hostnamereg

Chapter 3 Ethernet ConfigurationGPIB-ENET/100 for Mac OS 3-6 ni.com4. (Optional) You can enter a comment to help you identify the device.5. Click OK t

Chapter 3 Ethernet Configuration© National Instruments Corporation 3-7 GPIB-ENET/100 for Mac OSFor a Network without a Network AdministratorIf you are

Chapter 3 Ethernet ConfigurationGPIB-ENET/100 for Mac OS 3-8 ni.comVerifying the HostnameThe NI Ethernet Device Configuration utility automatically ve

Chapter 3 Ethernet Configuration© National Instruments Corporation 3-9 GPIB-ENET/100 for Mac OS4. Review the network parameter settings in the Propert

Important InformationWarrantyThe GPIB hardware is warranted against defects in materials and workmanship for a period of two years from the date of sh

© National Instruments Corporation 4-1 GPIB-ENET/100 for Mac OS4GPIB ConfigurationThis chapter describes how to configure your Mac OS computer to use

Chapter 4 GPIB ConfigurationGPIB-ENET/100 for Mac OS 4-2 ni.comFigure 4-1. Ethernet Settings in NI-488 Config3. To choose a GPIB bus to use with your

Chapter 4 GPIB Configuration© National Instruments Corporation 4-3 GPIB-ENET/100 for Mac OSFor more information about NI-488 Config, refer to Chapter

© National Instruments Corporation 5-1 GPIB-ENET/100 for Mac OS5Verify the InstallationThis chapter describes how to verify the software installation.

Chapter 5 Verify the InstallationGPIB-ENET/100 for Mac OS 5-2 ni.comConnecting the GPIB CableWhen you finish verifying the installation, you can conne

© National Instruments Corporation 6-1 GPIB-ENET/100 for Mac OS6Using Your GPIB-ENET/100and NI-488.2This chapter lists some general programming requir

Chapter 6 Using Your GPIB-ENET/100 and NI-488.2GPIB-ENET/100 for Mac OS 6-2 ni.com90 seconds at power on. In this situation, you will need to obtain a

Chapter 6 Using Your GPIB-ENET/100 and NI-488.2© National Instruments Corporation 6-3 GPIB-ENET/100 for Mac OSUsing the CFG RESET Switch during Operat

Chapter 6 Using Your GPIB-ENET/100 and NI-488.2GPIB-ENET/100 for Mac OS 6-4 ni.comUsing the CFG RESET Switch at Power-OnIf you want to reset the unit

Chapter 6 Using Your GPIB-ENET/100 and NI-488.2© National Instruments Corporation 6-5 GPIB-ENET/100 for Mac OSNoteThe NI Ethernet Device Firmware Upda

ComplianceFCC/Canada Radio Frequency Interference Compliance*Determining FCC ClassThe Federal Communications Commission (FCC) has rules to protect wir

Chapter 6 Using Your GPIB-ENET/100 and NI-488.2GPIB-ENET/100 for Mac OS 6-6 ni.com5. The utility prompts you to confirm the change you are about toper

© National Instruments Corporation A-1 GPIB-ENET/100 for Mac OSAPWR/RDY LED SignalingThis appendix describes how to interpret the PWR/RDY LED error co

Appendix A PWR/RDY LED SignalingGPIB-ENET/100 for Mac OS A-2 ni.comStep 1. Count the Long FlashesA three-second interval, during which the PWR/RDY LED

© National Instruments Corporation B-1 GPIB-ENET/100 for Mac OSBTroubleshooting andCommon QuestionsThis appendix describes how to troubleshoot problem

Appendix B Troubleshooting and Common QuestionsGPIB-ENET/100 for Mac OS B-2 ni.com• The entry in the Bus/Device menu should correspond to the busnumbe

Appendix B Troubleshooting and Common Questions© National Instruments Corporation B-3 GPIB-ENET/100 for Mac OSWhat do I do if I have installed NI-488.

Appendix B Troubleshooting and Common QuestionsGPIB-ENET/100 for Mac OS B-4 ni.comWhy does the NI Ethernet Device Configuration utility list my box as

Appendix B Troubleshooting and Common Questions© National Instruments Corporation B-5 GPIB-ENET/100 for Mac OSWhen should I use IBIC 488.2?You can use

© National Instruments Corporation C-1 GPIB-ENET/100 for Mac OSCSpecificationsThis appendix describes the characteristics of the GPIB-ENET/100 and the

Appendix C SpecificationsGPIB-ENET/100 for Mac OS C-2 ni.comSoftware CharacteristicsMaximum software transfer rate1...800 kbytes/sElectrostati

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radi

© National Instruments Corporation D-1 GPIB-ENET/100 for Mac OSDTechnical Support ResourcesWeb SupportNational Instruments Web support is your first s

Appendix D Technical Support ResourcesGPIB-ENET/100 for Mac OS D-2 ni.comWorldwide SupportNational Instruments has offices located around the world to

© National Instruments Corporation G-1 GPIB-ENET/100 for Mac OSGlossaryPrefix Meaning Valuem- milli- 10–3c- centi- 10–2k- kilo- 103M- mega- 106Symbols

GlossaryGPIB-ENET/100 for Mac OS G-2 ni.comDDHCP Dynamic Host Configuration ProtocolDNS Domain Name ServerEEMI electromagnetic interferenceFFCC Federa

Glossary© National Instruments Corporation G-3 GPIB-ENET/100 for Mac OSMm metersMB megabytes of memoryNNIC network interface cardSs secondsVV voltsVAC

© National Instruments Corporation I-1 GPIB-ENET/100 for Mac OSIndexAadding a GPIB-ENET/100to GPIB system, 4-1to network, 2-4CcablesEthernet connectio

IndexGPIB-ENET/100 for Mac OS I-2 ni.comEelectrical characteristics, C-1environmental characteristics, C-1error checking, B-5error code, A-1Ethernet a

Index© National Instruments Corporation I-3 GPIB-ENET/100 for Mac OSIIBIC 488.2using, 6-6, B-5information to record, 2-2INIT filesmanaging and renamin

IndexGPIB-ENET/100 for Mac OS I-4 ni.comNI-488 Configchanging NI-488.2 settings, 4-1example (figure), 4-2locating and starting, 4-1proper Ethernet set

Index© National Instruments Corporation I-5 GPIB-ENET/100 for Mac OSresetting default network characteristics, 6-4restartingafter using NI-488 Config

© National Instruments Corporation vii GPIB-ENET/100 for Mac OSContentsAbout This ManualConventions ...

ContentsGPIB-ENET/100 for Mac OS viii ni.comChapter 4GPIB ConfigurationConfiguring the NI-488.2 Software Characteristics...

Contents© National Instruments Corporation ix GPIB-ENET/100 for Mac OSFiguresFigure 1-1. GPIB-ENET/100 Front Panel...

© National Instruments Corporation xi GPIB-ENET/100 for Mac OSAbout This ManualThis manual contains instructions to help you install and configurethe